Question:
Domanda sulla frizione radiale.. bisogna apportare alcune modifiche a cavi o qualcosa per installare una rcs 16 brembo sul gsxr 1000 k5?? X il sensore di accensione con frizione tirata,cosa bisogna fare??
October / 01 / 2012
Answer:
La tua moto usa un cavo a filo per azionare la frizione, non puoi usare una pompa in alternativa.
Question:
Hi,I would like to ask if the Radial Clutch Master Cylinder Brembo 16RCS fits Yamaha YZF R1 '12 model. Your prompt reply is greatly appreciated. Thank you.RegardsKai
October / 07 / 2012
Answer:
If you watch your left hand bar you will notice your bike use a wired clutch lever therefore you can't use a master cylinder. But you can purchase a RCS look clutch lever to match the RCS brake lever look.
Question:
Brembo radial pump clutch 16 RCSI have a KTM690Rally Factory Replica Magura clutch pump Axial with a 11 mm inner bowler. His touch is very hard and requires a lot of force to operate or maintain the clutch driven semi-technical areas.I need to soften - reduce the driving force and it strikes me that a radial pump rate with respect'd get more. But I have doubts that are:We're talking about a clutch system where the Magura currently 11 mm. the end of travel of the handle is the end of travel of the piston of the transmitter. I wonder if riding the Brembo 16 mm. could be the case that at the halfway mark and would handle the clutch pressed fully and that would be disastrous because I fear that the feel of clutch would be useless to Off road with a tour so short. Is that correct?.Thanks in advance for the answer.
February / 25 / 2013
Answer:
Magura use mineral oil for clutch mc, therefore you can't use or switch to a master cylinder that not uses mineral oil.
Question:
Salve,questa pompa è perfettamente compatibile per 1198s 2010?,ho visto che è sprovvista di microinterruttore di sicurezza,posso montare l'originale o ne devo acquistare uno apposito?grazie per la disponibilita' a presto.
May / 15 / 2013
Answer:
La pompa è perfettamente compatibile, ti serve necessariamente un idrostop, non ci sono soluzioni alternative ne è possibile adattare lo switch originale. Questa risposta vale per tutte le moto.
Question:
I have a 2009 Suzuki Bandit 1250, i wish to replace the clutch master cylinder with a Brembro one. Can you tell me everything I need to do this including cables, reservoir etc ect. Also i'm looking at replacing my front brake master cylinder too, can you tell me the same for this. Thanks
July / 06 / 2013
Answer:
On your Bandit you can use for sure 19RCS + 16RCS. For both mc I suggest to install specific brake lines, you need in fact different banjos on mc side and also you will improve braking. To order the brake and clutch lines simply order the stock lines writing in the cart note field "for radial mc". Regarding Reservoirs there are multiple choices , from Rizoma to Brembo. I suggest to browse our site and choose the one you like maybe writing us back again once you find the one you like.
Question:
I already have RCS19 on my gilera Fuoco500 front brakes, can I also use the RCS 16 for my rear to get a match in brake lever feeling? Thanks
July / 22 / 2013
Question:
Hi, Is this master cylinder suitable for use on a 2011 Ducati 1198SP, are there any modifications required?
September / 28 / 2013
Answer:
You need just a switch stop , nothing else.
Question:
I need to replace my clutch lever on 2010 triumph speed triple. Do I need to replace master cylinders on both sides to use your levers? Also thinking about the same thing on my ducati monster 1100 evo.
October / 14 / 2013
Answer:
You can't replace a clutch WIRE lever with a master cylinder, so far this mc will fit only your Ducati.
Question:
Hi.I just wonder if this pump acept the original reservoir on my Kawasaki ZZR1400, or do i need to gat a complet set from Brembo?RegardTor Amdal
October / 31 / 2013
Answer:
As far I remember ZZR1400 has an external reservoir, therefore it works with this mc also. BTW please check the diameter of the oem mc, if it is 16mm choose a 17RCS
Question:
does it comes with the banjo bolt?
November / 18 / 2013
Answer:
It comes without any bolt.
Question:
I have installed a Brembo RCS16 Clutch lever on my VMax1200 and I have problem engaging 2nd gear upwards. The bike will move when I engage 1st gear too. Has anyone ever tried installing those on a Gen 1 Vmax before?? Is it suitable for Vmax Gen 1 ?? PLease help??PS: I am using Barnett Clutch Kit.thanks
November / 21 / 2013
Answer:
The solution to your problem is asking who sold the Barnett clutch which is the right master cylinder. For sure you need a different diameter piston.
Question:
hello - I am riding a MVAgusta Brutale 1090RR year 2013 and itend to change the stock brake and clutch master cylinders with brembo rcs 19 model. can you tell me the difference of the 19 and 16 rcs clutch model. I know the inner piston differs. what clutch model would you choose/recommend for a 1090 brutalethank you for you infochris
June / 13 / 2014
Answer:
19RCS shall be used only when you upgrade to bigger clutch slaves otherwise always use 16RCS: this info applies to every mc
Question:
G'day,I have a Brembo 19RCS brake cylinder. I will fit a 16RCS for the clutch. I want a pair of Rizoma mirrors, probably Rizoma 4D. What are the best clamps to suit this set up: - Rizoma or Brembo?I would like to stay with 8mm so I could still use the standard mirrors if I want to. I do not see an 8mm Brembo clamp listed in right hand thread, only left hand.CheersDeano
July / 16 / 2014
Answer:
Rizoma does not produce any 8mm clamp, so far you'd choose Brembo or other 8mm clamps.
Question:
G'day,What banjo bolt do I need with this cylinder to use it with the standard clutch line on my 2009 1078RR Brutale? Not clear from the photo if a bolt is included.CheersDeano
July / 25 / 2014
Answer:
One M10x1mm bolt. I suggest to order a pressure switch like "Brake Light Switch 10x1.0 mm, for one banjo"
Question:
I have 2005 Yamaha MT-01, what is the type of clutch master cylinder that I can chose?
August / 25 / 2014
Answer:
16RCS it is always the right choice for mid/high cc size motorcycles. BTW che the diameter of the oe mc, if is 16mm you'd better purchse a 17RCS.
Question:
Hello, I have a Brembo 19diaX20 stroke radial master cylinder. It is the old one piece lever type. Do you have any of the clutch master cylinders to match this brake in appearance? Cheers Ross.
September / 05 / 2014
Answer:
The closer is the CNC Billet 16x18.
Question:
would this fit a triumph speed triple 2014?
December / 06 / 2014
Answer:
For sure NO. Your bike use a wire clutch.
Question:
Hello, can i use the RCS19 on my 2013 multistrada 1200?
February / 07 / 2015
Question:
Hi there please can you tell me which Brembo rcs clutch master cylinder i require for my ducati 1199s with an EVR clutch slave cylinder and if i require anything else to make it completeThanks
February / 21 / 2015
Answer:
This question should be sent to EVR. We don't have the specifics of the parts we don't sell.
Question:
Could you price a hydraulic hose to convert from non-radial oem clutch cylinder To this RCS16 radial cylinder. Tuono 1000R 2008.Thanks
April / 21 / 2015
Answer:
Fren Tubo does not produce clutch hose for your bike. Won't be possible to produce a hose for you without having the specific of the original hose. If you can provide them please write to info@carpimoto.com
Question:
What is the right size RCS clutch pump for my Aprilia RSV 1000 mille-00
April / 23 / 2015
Answer:
16RCS the right choice ever. For motorcycle which stock clutch master cylinder piston diameter is over 13 mm. 14RCS the right choice for motorcycle which stock clutch master cylinder piston diameter is 11, 12 or 13 mmYou can see it in the lower part of your pump
Question:
what clutch master do i have to put on my 2014 ducati streetfighter to ease the pull? do i need to replace the slave as well ? will it make a considerable difference ?
May / 25 / 2015
Answer:
You can use 16RCS with stock slave master cylinder or purchase a CNC Racing bigger slave as well
Question:
hello there just would like to know if i can use this set up with nissin breaks, i have a 2001 vtr sp1 and am looking for aftermarket set up, a whole new clutch and break levers with master cylinders
May / 25 / 2015
Answer:
Good morning, yes you can use this clutch mc.
Question:
hi, will this fit my '09 ducati gt1000? I am using an aftermarket Oberon clutch slave, should I get 16RCS or 17RCS clutch master?
July / 14 / 2015
Answer:
If the master slave has the same size of the oem choose the 16RCS which is perfect for the standard slave diameter.
Question:
Looking for a matching brembo RCS clutch master for a 2011 hayabusa... Would this item be correct ? Regards John And do you combine shipping costs on multiple items ordered ?
July / 24 / 2015
Answer:
Yes it will be fine. We combine shipping costs.
Question:
Hi I am owner of a MOTOGUZZI 1200 Sport MY2007, I want to change the OEM for clutch with this one, will work right?
August / 16 / 2015
Question:
Hi, Can you please tell me if the rcs 16 needs a switch for the clutch on a Suzuki hayabusa 2009 As you have to pull in the clutch to start the bike. Thanks Paul.
August / 18 / 2015
Answer:
Yes , you should use Brake Light Switch 10x1.0 mm, for one banjo
Question:
Thanks for your reply to the question on hayabusa 09 clutch, can I use a micro-switch like the rcs 19 uses and dos this clip under the master cylinder. Thanks Paul.
August / 18 / 2015
Answer:
Not possible to use a switch.
Question:
Hi I have an xjr1300 99 year, with sigma slipper clutch and a slightly larger slave cylinder the slave is designed to be used on the standard master.My question is please do I require an RCS16 or a 19 ?Kind Regards John.
December / 20 / 2015
Answer:
Please check the diameter of the stock master cylinder, if it is 16mm you should use 17RCS.
Question:
Hi.,I am wanting a clutch and brake master cylinder combination for my Kawasaki ZRX 1200r. (rcs 19 for the brake ans rcs 16 for the clutch?)How much is it for the pair ..,and banjo bolts?Also what about reservoirs? Best regardsBrian Wells.
February / 28 / 2016
Answer:
Yes 19 + 16 is the right combination. Just add the two mc to the basket along with two Universal Radial Master Cylinder Adaptor Part Number: 170101 . For reservoir I suggest to purchase 19RCS premium kit that includes reservoir kit and one of the reservoir (+ one bracket) or the Brembo kit 110A26386
Question:
Hi as previous inquiry regarding Ducati hypermotard evo 1100sp brembo suitable clutch master upgrade as recommended using RCS-16. Now presently i using STM clutch slave and STM slipper clutch; would RCS-16 still the most suitable upgrade set or others model such as RCS17 or 19.? Please advise before i make my order. Thank q.
April / 07 / 2016
Answer:
If right now you are using stock master cylinder without any problem the upgrade is 16mm or 17mm, otherwise you should ask STM which is the correct piston diameter.
Question:
Hello,I need a replacement unit for my Ducati 999s. Which unit will be direct replacement?I use the bike for street and sport only.Tom
April / 11 / 2016
Answer:
This part is correct. You need also one Brake Light Switch 10x1.0 mm, for one banjo
Question:
I can install radial cluch master cylinder brembo 16 rcs 16-18 . My motorcycle is suzuki b king 2008. ? Thank you.
May / 14 / 2016
Answer:
Please check the diameter of the stock master cylinder, if it is 16mm you should use 17RCS.
Question:
Hi!"16RCS" clutch master for Honda VFR750 RC24 (1988)?
June / 02 / 2016
Answer:
I think so, but I can't confirm 100% . Check the diameter of your oem master cylinder clutch piston, if it is 13mm or 14mm it should be fine.
Question:
hello, i bought with you a 19RCS brembo master cylinder, and want to know if the Radial-Clutch-Master-Cylinder-Brembo-16RCS is the best choice for my bike HONDA CBR1000RR 2005 repsol. Because i don't know the OEM piston diameter of the radial clutch master cylinder.
June / 09 / 2016
Answer:
Usually the stock clutch master cylinder is a 13 or 14mm, therefore you can use 16RCS.
Question:
I am getting a Panigale R 2016. I have already ordered a larger slave cylinder so I was wondering if the 17RCS was the way to go
June / 19 / 2016
Answer:
We can't provide this info, You should ask to the slave manufacturer which is the recommended diameter.
Question:
I have a ducati 1000 ss ie do i need a new clutch line or is there an adaptor needed for the 16RCS
June / 26 / 2016
Answer:
New line or the Universal Radial Master Cylinder Adaptor
Question:
Is the 16RCS clutch master cylinder the correct choice for a Ducati 996, year 2001 with standard slave cylinder ?And if I am going to mount a slipper clutch this winter, will it still be ok ?
August / 29 / 2016
Answer:
16RCS replaces the oem clutch master cylinder . Slipper clutch: you should ask to the slipper clutch manufacturer , if it works with oem mc will be ok, if it requires an upgrade they should tell you.
Question:
Hello, i have a problem with the clutch leaver rcs 16 - the clutch muster cylinder works fine but today starting to do some streange clicking noise whet it is push? May you known this problem? What should i do?
September / 02 / 2016
Answer:
Hello, have you recently washed your bike? The clicking noise your hear may be just a lack of grease on the pin
Question:
Ok thank you - what i should pick up in store to fix this problem? what kind of grease? Thank you in advance...
September / 03 / 2016
Answer:
Hi, you can use a common grease for mechanical parts. This noise may persist, because it's a mechanical noise due to the sliding of the pushrod and piston.
Question:
Hi there. could you please recommend a brembo clutch master cylinder for my 2016 zzr1400 performance sport, I'm thinking of buying the 19 rcs off you thanks adrian
November / 13 / 2016
Answer:
Hello, we can't confirm, need to check the piston diameter of your stock mc, the aftermarket MC should be as similar as possible to the OEM piston. Usually it is a number stamped over the master cylinder body.
Question:
I have a 1986 BMW R65. Does this clutch master cylinder work for cable clutches?
December / 12 / 2016
Answer:
No: Cable clutches use just lever + perch, not a master cylinder.
Question:
if i put these on my multistrada enduro 2016, what benefits could it provide me ?
December / 17 / 2016
Answer:
Smoother clutching. I suggest also 30mm master slave cylinder.
Question:
I need a good clutch master cylinder replacement for my Morini Corsaro Veloce 2008 (radial type), or a revision set for the original.What size would work best for the Corsaro, and which size brake master cylinder would be perfect for street use?
February / 06 / 2017
Answer:
Hi, Brembo suggests you 16RCS clutch MC, code 110A26350 and 19 RCS brake MC code 110A26310
Question:
Is this clutch master cylinder serviceable?
February / 07 / 2017
Answer:
Yes. Can be overhauled in Brembo factory only.
Question:
I own a Guzzi 1200 sport 2014 , the clutch is toch heavy for me , which clutch master canhelp me to make the hendle operation much more lighter ?
March / 19 / 2017
Answer:
None, the bigger piston you choose the harder will be. You have a 12mm piston, the only solution is to work on the master slave.
Question:
Hi I am riding 1098s and looking for this clutch. Do I need the brake light switch or any other stuff? Thanks
August / 12 / 2017
Answer:
You need a pressure switch stop M10x1mm for single banjo.
Question:
Hi, I'm using rcs16 master cyclinder for my gixxer 1000 k7 as it uses hydraulic clutch. Can I buy the safety/micro switch? As I need to clutch in to start and for launch control need to use switch. Thank u.
August / 14 / 2017
Answer:
Clutch can't use switch. You can mount M10x1mm single pressure switch bolt only.
Question:
Hi I am looking to replace a 14mm clutch master cylinder on a GSXR1100W from 93.Would you know what the ratio of these nissin cylinders are?The reason is that I am looking to use a 16x18 radial master but would like to calculate the amount which the slave cylinder would move in order to tune the clutch push rod length.many thanks
September / 27 / 2017
Answer:
Ratio: you can measure on your clutch master cylinder, it is the distance between fulcrum and piston rod.
Question:
Hello~My Ducati monster796 have a micro switch in OEM clutch lever. If I upgrade to 16RCS, how can I keep the micro switch work in 16RCS? or need to bypass the micro?
February / 28 / 2018
Answer:
Hello, you can shall use pn 0626MQ20.
Question:
Hi~I would like to buy Brembo 16rcs for upgrade my monster 796, but I have a question is: how to collect my OEM clutch lever micro switch?
April / 10 / 2018
Answer:
How to connect? You shall use the "Brake Light Switch 10x1.0 mm, for one banjo"
Question:
Hello,I have a 2015 Ducati Diavel and want to install a set of RCS 19 for the brake and 16 or 17 for the clutch master. I have a stock slave cylinder. Which is a better application the RCS 16 or 17 for the diavel, considering it has a slipper clutch? (I don't know the diameter of the original slave clutch).Also, for mechanic supervision, what does he have to look out for (not the best mechanic available here).Many thanks in advance,Alex
May / 07 / 2018
Answer:
Hello, the correct replacement for stock clutch master cylinder is 16RCS. You can see the clutch MC diameter below the body , check it before place the order.
Question:
Hi, I have a bimota SB6 with a suzuki gsxr1100 engine.The clutch slave cylinder is a diameter of 35.7mmWhich brembo clutch master cylinder will be suitable to work with this slave cylinder?
June / 06 / 2018
Answer:
The answer is over your bike: you shall check which is the diameter of your clutch master cylinder, and then purchase the closest diameter. Unless you do not have any problem right now, this will be the correct choice.
Question:
Hi i replaced my clutch with the brembo 16RCS for my r nine t for about some time now and i noticed the clutch fades..i found out that bmw requires mineral oil so,we drained the DOT 4 and replaced it with mineral oil but the orings and the rubber on the reservoir expaned ...is brembo compatible with mineral oil
June / 28 / 2018
Answer:
No it is not (there is an answer above about a KTM).
Question:
Estimados. Tengo una ducati multistrada 1100 año 2007 y sufrió una caída en la cual la bomba sufrió daño , solo este modelo es compatible con dicha bomba o puedo encontrar la original en el mercado ya que la he buscado por todas partes y no encuentro ni siquiera el kit de repuesto de los retenes. Se agradece su respuesta.Iquique, Chile
July / 07 / 2018
Answer:
Hola. Esta parte es correcta para tu motocicleta. El cilindro maestro original es difícil de encontrar en el mercado porque no es un producto típico de Brembo, es decir, el oem no tiene el depósito de líquido de frenos por separado.
Question:
I have a 2014 Hypermotard 821. Im installing the Ducabike Hydraulic clutch conversion kit. This kit comes with the ride by wire connectors. Is there any Brembo Clutch master cylinder that is compatible with ride by wire?
August / 20 / 2018
Answer:
Ride by Wire is a Gas Throttle system, I don't understand how could be involved the clutch. If you are talking about the swithc that is always installed on clutch levers, the Brembo MC has not any switch, you should use a pressure switch. If you want to send a more detailed question we will be happy to answer again.
Question:
HiI have a Ducati 749S from 2004. Will the Radial Clutch Master Cylinder Brembo 16RCS fit?Is it possible to use the existing microswitch, that allows you to start the engine while it is not in neutral?
September / 06 / 2018
Answer:
This is the right clutch mc, it comes without switch. You shall purchase "Banjo Bolt with Buil-In Pressure Brake Light Switch 10x1.0 mm, for one banjo" . You need also reservoir + bracket.
Question:
I have a 2018 Husqvarna 701 Supermoto. Would the 14RCS Clutch Master Cylinder work on my bike ?
February / 03 / 2019
Answer:
We don't think so, the stock master cylinder is 11mm, if you use a 14mm you won't be able to push the lever as hard it would be and it could not be possible to run all the clutch stroke.
Question:
Question:I have a 2018 Husqvarna 701 Supermoto. Would the 14RCS Clutch Master Cylinder work on my bike ? Answer:We don't think so, the stock master cylinder is 11mm, if you use a 14mm you won't be able to push the lever as hard it would be and it could not be possible to run all the clutch stroke.Even though it says this ->14RCS the right choice for motorcycle which stock clutch master cylinder piston diameter is 11, 12 or 13 mm
February / 06 / 2019
Answer:
The sentece you read "14RCS the right choice for motorcycle which stock clutch master cylinder piston diameter is 11, 12 or 13 mm" it is the commercial Brembo claim we copied and pasted here; but We confirm what We wrote: If you use a 14mm instead of 11mm the lever will be very hard, then you could not find a real improvement changing the master cylinder.
Question:
I am replacing the OEM Brembo Clutch and Brake master cylinders on my 2000 Ducati 996 Strada. Is it possible to get this as a kit similar to the "RCS17PKB Radial Brake Master Cylinder Brembo 17RCS Premium Kit Black"? If not, is it possible to get the "Bracket + Reservoir Mounting Kit for Brembo RCS Clutch Master CylinderPart Number: 110A26386" in black/smoke similar to "Brembo Brake/Clutch Fluid Light Smoke Reservoir 15cc, sloped outflow, Vertical wingProduct code: 10444653"? Thanks.
April / 06 / 2019
Answer:
Not possible, not produced by Brembo. If you want to use asmoke reservoir you need to purchase separately
Question:
Hi, can you tell me what type RCS I need for a Moto Morini Granpasso with micro switch?
May / 26 / 2019
Answer:
Brembo does not produce any RCS for clutch with micro switch.
Question:
Acquistare Brembo 16 rcs e usarlo per freni, non frizione.Posso usare la funzione correttamente se compro il cavo freno separatamente e lo monto su 16CS?
June / 25 / 2019
Answer:
Si certo, è una pompa che si può usare anche come pompa freno. Yes sure you can use it also as brake master cylinder.
Question:
Hi, Since the clutch system of my R 9T accept mineral oil is your cylinder okay to use.?I ve heard many time that the rubber part will ruin under the mineral oil and bmw part will under dot4.
August / 31 / 2019
Question:
Can you use the 16rcs clutch master cylinder with an oversized 29mm slave cylinder and a slipper clutch on a Ducati?ThanksRichard
September / 06 / 2019
Answer:
You can use with 29mm master slave. You can use on a slipper clutch which is compatible with 15 / 16 mm clutch master cylinder
Question:
HelloI have an rcs 16 clutch on my gsxr 1000 k7 which it lost pressure. Is there any replacement kit to fix it?
October / 11 / 2019
Answer:
No, shuld be overhauled by Brembo
Question:
Hi guys. I have a 2008 ducati 848 with a Pramac racing 30mm clutch actuator and a ducabike slipper clutch. Any idea on which clutch master cylinder would be best. Thanks in advance. :)
December / 02 / 2019
Answer:
This one for sure will be fine.
Question:
Hello I have a 2008 CB1300 w/ABS I use the OEM brake lever with a Brembo M4 radial caliper and the OEM clutch (hydraulic) and want to uprgrade them both. What Brembo MCs would you recommend? Will any other equipment be needed? Is ABS going to be a problem?
December / 09 / 2019
Answer:
With M4 use 19RCS. Regarding Clutch you should get the piston diamter and the purchase the closest Brembo master cylinder . Diameter is impressed over the oem clutch master cylinder.
Question:
Hi, what is the recommended size for 2011 Dorsoduro 1200 ABS? 19RCS for brakes, 17RCS for clutch?
December / 27 / 2019
Answer:
Stock Brake is a 15mm Brembo Master Cylinder therefore we recommend 17RCS for brake. Stock Clutch is a 13mm Brembo Master Cylinder therefore we recommend 14RCS or 16RCS for clutch.
Question:
Hi guysI have a moto guzzi griso SE, 2009, 15000 miles (UK bike). The clutch lever is VERY heavy. I could replace it with a new guzzi clutch cylinder OR BUY FROM YOU the Brembo clutch master cylinder with lever, part number 110A26350. Can you please confirm three things before I order :(1) will this make the clutch operation easier ? (2) is this the correct part number for my bike ? (3) do I need to order an other part to fit the new brembo clutch cylinder/lever ? Thank you.
January / 27 / 2020
Answer:
Stock clutch master cylinder is a Brembo PS12 pn 10777011, then a 12mm therefore 1) it won't be easier because it is a 16mm, 2) it is not correct because is too big , we recommend to purchase a new 12 or 13 mm or a 14RCS .
Question:
Thanks you for your answer on my griso clutch cylinder. Can I purchase from you the part you recommend (Brembo PS12 pn 10777011) ? Do your recommend 12,13 or 14 RCS ?thankyou.
January / 29 / 2020
Answer:
Brembo PS12 pn 10777011 is a discontinued part, it is replaced by pn 10A03911 which will be available for ordering on our site in about two days
Question:
Looking at 16RCS to replace the old clutch lever/cylinder on my 2013 Ducati Monster 696. Do I need anything else besides the MC, resevoir kit and a Banjo switch to do the job?
April / 27 / 2020
Answer:
You need for sure reservoir kit, banjo switch, mirror clamp, banjo adapter. We recommend to use 14RCS.
Question:
Ahoj chcem namontovat na ducati monster 1100 evo brembo 19rcs bude pasovat? A spojku 16rcs?
June / 02 / 2020
Answer:
Thank you for contacting us through our website. Yes We confirm this part is correct.
Question:
Hi, I want to fit RCS to brakes and clutch on XJR 1300 2006 will it be 17 RCS for clutch and brakes and do they come with switches, banjos and crush washers?
June / 11 / 2020
Answer:
Brake: Yes 17RCS is corect. Clutch: Please check the diameter of the stock master cylinder, if it is 16mm you should use 17RCS. Only Brake mc comes with switch.
Question:
For a Ducati 800ss with a yoyodyne slave, which I think is 29mm and I believe a stock clutch MC of 12mm, would the rcs14 be the correct replacement? Would there be any benefit to going to the rcs 16 like decreased effort in lever pull? Appreciate your help.
June / 24 / 2020
Answer:
The stock mc is 13mm, we recommend 16RCS which is a 15mm or 14RCS as well. The bigger is the diameter the harder will be the lever pull.
Question:
Hello. I'm looking for a Brembro RCS clutch master for my ducati 1198s 2010.I have a slipperclutch ,stock slave and the bike is used for racing only, should I choose the 19rcs? Or the 16rcs?
June / 30 / 2020
Answer:
Which master cylinder are you using now ? Your stock master cylinder ? If so and works fine use 16RCS. If you have problems then ask to the slipper clutch manufacturer which diameter is correct .
Question:
Hello,I have bought in your e-shop Radial Clutch Master Cylinder Brembo 16RCS, Fold-Up Lever, 16-18 ratio. Is there shorter lever to replace original one which is supplied with Radial Clutch Master Cylinder Brembo 16RCS, Fold-Up Lever, 16-18 ratio ? Can you recommend me ?
September / 08 / 2020
Answer:
There is not a shorter lever. The shorter lever for Brake 110A26396 is compatible BUT the logo Brembo will be upside-down, that's why we do not list as compatible
Question:
Which Brembo Clutch MC is OK for a 2010 Guzzi Griso 1200? Is RCS16 OK?
September / 26 / 2020
Answer:
As far we know the stock Brembo master cylinder is pn 10777011 a PSC 12 then 12mm, you'd better use a 13 or 14mm , then a 14RCS.
Question:
Hello I have a 1984 Honda vf1000r and I tried 16rcs clutch and it did not work correctly. Which clutch master should I get?
April / 06 / 2021
Answer:
We don't know. To answer we should know the oem piston diameter. You should choose then the closest to.
Question:
Model Ducati Monster 900 1997 Hi What Brembo Clutch/Brake Master Cylinder do you recommend?16RCS & 15RCS ?Thanks
June / 22 / 2021
Answer:
Stock Brake is 16mm, we recommend 17RCS. Stock Clutch is 13mm, we recommend 16RCS .
Question:
I am currently riding a R15 V3 2021. Can you suggest which model clutch or brake i should use? Thanks
July / 24 / 2021
Answer:
Your R15 mount a wire clutch therefore NOT a Clutch Master Cylinder. On Brake side use 14RCS.
Question:
helloMy bike is a Suzuki GSXR 1000 K8. I have installed a Brembo RCS 19 brake master cylinder on my bike and know I need a clutch lever to match. My clutch is hydraulic. What is the lever that I need to fit on my cluth master cylinder OEM? Thank you
September / 15 / 2021
Answer:
Ther is no lever that will match. In this case the matching left side choice is a Brembo Clutch master cylinder
Question:
Hello there on a Aprilia Caponord ETV1000 I need to replace the clutch pump but also to make it a bit softer,what is the correct size to get ?Also please the right size for the brake pumpThank you in advance Vassilis
September / 30 / 2021
Answer:
The stock mc is PSC 12/25 therefore 12mm. If you want a softer lever you must keep same or lower size. You can't use any bigger diamter master cylinder.
Question:
Hi,I ride a 2009 Yamaha MT 01. I believe the stock clutch master cylinder is 17mm. What do you recommend for the brembo RCS? 16/17 or 19RCS?
October / 23 / 2021
Answer:
If the stock diameter is 17, choose 17RCS
Question:
Hi, i’m using XMAX 250, M3 single caliper (front) and p32 (rear). I want to use RCS on both brakes. What model of RCS would you recommend? Thanks
November / 24 / 2021
Answer:
We don't know what is a M3 caliper, btw on a scooter with one single front caliper we recommend 14RCS, for rear as well 14RCS (left)
Question:
I’m using brembo m3/k50 caliper (4 piston, single disc) for front and brembo p34 caliper (2 piston, single disc) for rear. What RCS master rem you would suggest?
November / 24 / 2021
Answer:
We don't know the caliper you are mentioning, if we type the name in the google search bar looks like they are the M32B. If so it is a claiper that when used as double disks requires a 17mm, when it is a single caliper / one disk can be used with 14RCS or 15RCS. Then You can use 2x 14RCS (one 110A26345 right and one 110A26365 left) or 15RCS for front brake and 14RCS 110A26365 for rear brake .
Question:
Hello, I have a Ducati Monster 821 Stealth. I plan to change to 16 RCS Clutch MC from stock. Do I need anything else besides a reservoir?
November / 28 / 2021
Answer:
Thank you for contacting us through our website. We regret to inform you that this part is not correct. Monster 821 use a wire clutch perch therefore you can't use a master cylinder.
Question:
Hi, I have a 2002 Ducati Monster 620 ie (dual disc) with two Brembo P4-30/34 calipers in the front and I would like to upgrade to the radial master cylinder. It is for city riding and I would prefer longer travel and better feel. Is this 16RCS the right choice, or should I go with 17RCS or 15RCS? I would also like to upgrade the stock hydraulic clutch master cylinder - would the 14RCS be a good option there? Thank you
June / 05 / 2022
Answer:
This is a clutch master cylinder. Since stock clutch is 13mm we recommend 14RCS. Regarding Brake: please post your question inside the brake master cylinder
Question:
Hi, I have a 2021 Husqvarna 701 and I ordered a brake master cylinder RCS 15, which clutch master cylinder is recommended since I want to have matching levers. Thank you.
August / 07 / 2022
Answer:
2021 Husqvarna 701 could be ENDURO, VIPTILEN , SVARTPILEN . The stock clutch master cylinder diameter is, for all these models, 11mm therefore you can't use any Brembo RCS because RCS min diameter is 14mm.
Question:
It's a 2012 ducati hypermotard1100evo sp. I don't know the size of the stock master cylinder. Can I just order the 16rcs? Are you 14rcs?
March / 25 / 2023
Answer:
Thank you for contacting us through our website. Yes We confirm this part is correct.
Question:
Hello, can i use the 110A26350 16RCS on my 2007 monster s4rs ? (With OBERON Slave Cylinder for Ducati ( CLU-0116 )
May / 08 / 2023
Answer:
Oberon product page do not specify the slave piston diameter, we can't answer.
Question:
Ducati Monster M900 1997 , premium black kit available?16RCS still recommend with a , 30mm diameter Clutch Slave Cylinder,
June / 16 / 2023
Answer:
16RCS is correct. If you want black reservoir kit add Part Number: 110A26376
Question:
Hi What do you recommend for a Ducati 748s STM Slipper FDU-S032 and Oberon 29mm clutch slave
July / 03 / 2023
Answer:
We don't know. The answer should be provided by the two manufacturers. Usually they provide the correct cluth master cylinder piston diameter. Please note 16RCS is a 15mm piston master cylinder .
Question:
Ciao! Quale frizione Brembo RCS consigliate? La dimensione di fabbrica è 19 mm. ZZR1400
October / 21 / 2023
Answer:
Se hai una 19mm devi sostituirla con una 19mm. Noi non abbiamo controllato dal vivo la moto per cui non possiamo confermare che sia di serie 19mm.
Question:
Will this fit a KTM SuperDuke 1290R ‘22 or do you have a suggestion for this bike? Brake master will be Brembo RSC17.
February / 17 / 2024
Answer:
It won't be a correct choice because your stock master cylinder piston is 12mm. You need to change the master cylinder slave.
Questions & Answers placed here are related to the nature of this product, how it works, where it works, if it is useful etc etc, if you need help on another part please do not place your question here but inside its page.
This is not either the right place where to ask for price, availability, delivery, shipping, for this info click on "MyCarpiMoto" and then "Contact" at the top of the page.
Your Privacy: Do not add any personal information inside the question box, such as name, email, phone, everyone would read it; to protect your privacy, every question which includes personal informations is by default canceled.